Ice machine installation precautions and uses
An ice machine is a refrigeration machine that produces water by cooling water from a refrigeration system through an evaporator. According to the principle of the evaporator and the generation process, the shape of the generated ice is also different. Generally, the ice machine is divided into a particle ice machine, a flake ice machine, a plate ice machine, a tube ice machine, a shell ice machine, etc. according to the ice shape. . According to the use and characteristics of ice itself, ice is mainly divided into: tube ice, block ice, granular ice, flake ice (fresh water sea water), plate ice (fresh water sea water), transparent ice, ice water. No matter which type of ice, it is determined by its characteristics. According to the shape of ice, it can be divided into: scaly ice machine, snowflake ice machine, ice machine, ice machine, ice machine (can be divided into small ice machine and industrial ice machine), ice machine, Granulator, tube ice machine, bullet ice machine. The ice machine has a large amount of work and a long working time. Therefore, there must be good installation, maintenance and maintenance. Many ice machines are not installed and need to be installed by themselves. Now we will introduce some problems that should be paid attention to when installing the ice machine. I hope to give you exchanges and learning. 1. The location where the ice machine is installed. To be installed in direct sunlight, the ventilation is good. The ambient temperature in winter should not be too low outside, because the water pipes installed in the outside machine are easy to freeze. The minimum ventilation distance of the condenser is at least 1 meter above and below the obstruction and at least 50 above the roof. It is better to have a larger ventilation distance, and you must keep the air flowing and not let the wind go. If you can't find a suitable time, you can install a large and small suction device to allow the new wind to exchange heat. 2. The ice machine should be installed on a solid ground. The machine should be installed horizontally without tilting. Otherwise, the machine will vibrate when it runs, and if it is too large, it will save the water in the refrigerator and affect the quality of the ice. 3. The ambient temperature of the ice machine is 5-38. The ambient temperature directly affects the ice production. This is why some customers often say that the summer ice is slow. The water temperature of 3-30C water temperature also affects the amount of ice produced. The water temperature is inversely proportional to the amount of ice produced. 4. After the ice machine is in place, first check whether the appearance of the machine is damaged, whether there is any foreign matter in the ice-falling passage, whether the fan blades are flexible or not, and whether there are oil traces in each joint of the unit. Check that all shut-off valves of the unit are open. Here is the place that should be opened. Check if the oil level of the compressor is above the oil level and if there is no oil. The oil pair has a lot to do with the service life of the compressor, so I hope everyone pays attention to the oil level and the color of the oil. 5. Check the voltage of the customer's home and the size of the air switch. The ice machine should have its own separate water valve and power supply for future maintenance. 6. Turn on the water source. If the water pressure is normal, the water pressure will be too low, which will cause the old alarm of the machine. If the customer's water pressure is stopped or the old water is stopped, it is recommended that the customer save the water tank and the booster pump. The water level of the inlet tank should be low and about 10 mm from the overflow. The water level can be adjusted by adjusting the float. 7. Do not cool down immediately after the machine is powered on. The crankcase heater should be able to warm the oil, but some machines are not necessary. Taikang is a heating belt. 8, the unit is running. Listen to the crew running sound. Look at the icing of the evaporator, and some machines need to add salt water. Generally 30KG barrels plus 200 grams of salt is good. The specific situation can be seen by yourself. Salt is used for the quality of ice and the shedding of ice. Also look at the water level of the water separator is normal. I saw in some stores that the water pressure was too large and there was water on the side of the ice. At this time, you need to close the water valve in front of the water separator, it is very simple, not much to say here. 9. Observe the frosting condition of the press, frost return to the compressor's return air valve or the return air pipe press. Prevent liquid slamming, if the amount of fluorine is not much, you can adjust the defrosting condition by adjusting the expansion valve. 10. After the unit is running normally. Test the protection function of the unit. Water shortage protection by hand to the float switch is the water level float switch, connected to two lines, in fact, is a water level sensor to press him. The machine should be shut down. The full ice stop function should block the power switch by hand. Generally, the unit should stop for three minutes. Now the machine is stopped by the first press, and after half a minute the skate is stopped. This advantage is for the next start. The ice of the entire ice bucket is scraped off to facilitate the thickness of the next ice. After all the tests are normal, look for the engineering department to sign. And instruct the engineering department to repair the operation of the unit, as well as daily maintenance. Regarding the use of ice machines, in general, the role of ice is divided into three types: one for cooling, two for eating, and three for artificial scenes for viewing. Subdivided, the ice machine is widely used in industries such as aquatic products, food, supermarkets, dairy products, medicine, chemistry, vegetable fresh-keeping transportation, marine fishing, etc. With the development of society and the continuous improvement of people's production level, the industry with ice is coming. The wider the variety, the higher the quality of the ice. The requirements for "high performance", "low failure rate" and "health" of the ice machine are becoming more and more urgent. To sum up, the ice machine is currently used in the processing of aquatic products, meat processing, food processing, supermarket and aquatic products, long-distance transportation, laboratory, medicine, chemical, artificial ski resort, etc. The industry is also widely used and used in concrete engineering. Tetanus Vaccine,Hepatitis B Vaccine For Adults,Tetanus Booster,Td Vaccine FOSHAN PHARMA CO., LTD. , https://www.fospharma.com