Correct use of fruit trees for light and slow release
For fruit trees that are trimmed using the light-cut, slow-displacement pruning method, it is possible to increase production in the first few years after cutting. However, if this pruning method is used improperly, it will have adverse consequences. First, light and slow release Light-cutting is the degree of pruning should be light, and the amount of pruning should not be large. Slow release is also called dumping, which means that some branches of fruit trees are not pruned. Naturally, they continue to grow. Everyone is accustomed to consider it as one of the pruning methods. Light shear and slow release are closely related. Slow laying, short cutting, sparse cutting (also called thinning) are methods of pruning fruit trees, all of which have a weakening effect on the fruit trees as a whole, and they have a growing effect on the fruit trees. In the sapling growth stage of fruit trees, the greater the amount of pruning, the more pronounced the dual effects of this weakening and enhancement. Fruit trees that are pruned mainly with light shears will have the following performance: 1, the main trunk, but the main branches, lateral branches more verbose and weak, the skeleton formed by the crown is not strong. 2. There are many branches and large amounts of growth, but the growth length of new shoots is decreasing year by year, and the leaves are small and light in color. That is, or trees can increase production for a few years, and the tree vigor can also decay very early. 3, can ease the growth potential of the tree, the early formation of flower bud flowering results, but because the branches, leaves too dense, will affect the light within the crown, the mistletoe in the crown will increase, the flower bud differentiation is not substantial, the flowering rate is low, the knot The fruit is small. 4. The crown can be formed quickly. The canopy quickly formed, but the resulting parts moved outwards quickly. There were fewer results within the canopy and the yield was low and unstable. Second, light shear should be used properly Pruning the weight of fruit trees is not the key to affecting the yield of fruit trees. The availability of sufficient nutrients for the trees is the basic factor that affects the yield. If there is not enough fertilizer and water, the tree will not produce high yields whether it is heavy cutting or light cutting or slow laying. Although the heavy cutting will also make the branches prosperous, but that is, or flowering, the fruit setting rate will not be high. Young apple trees are characterized by strong growth. To ease the growth potential of the trees, the light shearing and slow release of the pruning can spread the nutrients, prevent the branches from becoming long, favor the transformation of the vegetative branches into fruiting branches, and early formation of flower buds and early high yields. Saplings should be lightly cut and put slowly. In the fruit period, there are many trees, many flowers, and many results. Heavy short shoots with multiple flower buds and some flower buds can be used centrally to enhance nutrition, prevent premature aging, and prolong fruitful age. It is reasonable to cut heavy trees in full bloom, and should not be lightly cut. The slow release of shoots can increase the germination rate, increase the number of shoots, ease the growth of branches, promote flower bud formation, early results, and early high yield. However, if there are too many twigs, or if the twigs are put slowly in successive years, the tree vigor will soon weaken, the branches will be long and thin, and the resulting parts will move outwards. The fruit of the knot will be of poor quality, and it will be prone to large and small annual results. Therefore, it is wrong to cut branches with short cuts when pruning fruit trees. At the same time, it is not appropriate to put branches as slowly as possible. In general, it is best not to slow down leggings, standing branches and competing branches. If we must put it slowly, we must take measures to deal with it, such as girdling, circumcision, twisting and other branches. If you do not deal with it, it will happen. High Precision Distance Sensor Laser range sensors combine the advantages of a visible red sensing beam with the increased range of a laser. The optical distance sensor devices are Class 2 lasers, support Class 1 customized. The high precision autonics distance sensor is successfully be used to connect to Arduino, Raspberry Pi, with +-1mm to 3mm high accuray, and long-range solutions (max up to 150m) for your application. Precision Distance Sensor,Precision Laser Distance Sensor ,Precision Distance Sensor Laser,Accurate Laser Distance Sensor Chengdu JRT Meter Technology Co., Ltd , https://www.cdlaserdistancemodule.com