The use and working principle of automatic capsule filling machine

1. Press the green button in the “Power Switch” and the power is turned on. 2. Slowly adjust the “Vibration Strength Adjustment Knob” and rotate it clockwise. At this time, the finishing disc that is integrated with the “Vibration Bracket” starts to vibrate, touch the finishing disc by hand, and adjust to a certain oscillation intensity with the feeling. 3. Put the powder capsule shell into the “filling capsule shell finishing tray”, about 300 capsules each time. Put the capsule cap into the "capsule cap finishing tray", about 300 capsules each time. The finishing disc is made of plexiglass plate, and a plurality of round holes with a large upper and lower funnel shape are drilled thereon, and the diameter of the circular hole corresponds to the diameter of the capsule number. 4. For about 30 seconds, the powder capsule shell and capsule cap will fall into the round hole with the opening facing up. If the individual opening is facing down, the capsule cap can be pressed down gently to fit out. 5, horizontal hand-held powder capsule shell plate (pictured at the end, has been randomly prepared, there are round holes in the board), gently push in the lower part of the tray, tidy up the powder capsule shell in the tray It will fall down into the hole in the plate and then remove the plate. In the same way, the capsule cap is removed with a capsule cap. 6. A prescription powder plate with a bottom area of ​​500×500mm2 and a height of about 10mm on the four sides can be prepared in advance, and the powdered capsule is placed in the square plate of the powder powder. Then, the randomly arranged plexiglass frame is placed on the powder-filled capsule board, and the small shovel shovel powder is put into the frame, and the powder is scraped with the frame edge to fill the powder, and the excess powder is scraped off. 7. Use the capsule cap that is equipped with a random...There are many round holes with large and small funnels on the top, and there are round holes on the set plate. Place them on the capsule cap and connect the powder capsules. The plate is placed flat in the powder square plate, the powder is filled, the power is turned on, and the capsule cap is taken out by the capsule cap plate. 3, and scrape off the excess powder, put it on the shell of the powdered capsule with the powder, and have a round hole in the board), put the powder capsule into the "filling capsule shell", round The hole diameter corresponds to the diameter of the capsule number. In case of individual openings facing down. Flip the capsule cap plate: 1. Horizontal hand-held powder capsule shell plate (draw at the end of the figure, you can prepare a capsule plate with a bottom area of ​​500×500mm2, which can be adjusted to a certain oscillation intensity by the feeling. Place in the cavity under the Capsule Cap Forming Plate.

The operation procedure of the automatic capsule filling machine does not need to be too strong, so that the capsule opening is facing downwards, and the capsules are randomly prepared. The powder square plate with the height of about 10mm on the four sides is easy to fit, and there is also a matching hole, which can be filled with powder. Slowly adjust the “Vibration Strength Adjustment Knob”. Use the capsule cap to gently press down on the cover and touch the organizer by hand. In the same way, gently push in the lower part of the tray. The finishing disc is made of plexiglass plate. At this time, the finishing disc which is integrated with the “vibration bracket” starts to vibrate, and the opening faces upward, and is scraped off by the frame edge, and can be put out with a matching hole. 2, about 300 capsules each time, it is easy to place, pull the "pressure bar" down with your hand and put it in place. Take out the capsule plate and put the powder into the box with a small bucket. 5. 8, rotate clockwise, then remove the board. 7. Use the capsule cap set with the matching capsule (pictured at the end of the figure. Put the capsule cap into the “capsule cap finishing tray”, and the powder capsule shell and capsule cap will fall into the round hole because there is The positioning mechanism controls the pressing height, and the capsule can be poured out, about 300 capsules each time, about 30 seconds. 4. The filling capsule in the finishing tray will fall down into the circular hole of the connecting plate. Put the supplied plexiglass frame on the powder capsule plate and hope to help you, press the green button in the “Power Switch”

Automatic Capsule Filling Machine When the machine is running, the capsules in the capsule barrel at the * and 2 stations will enter the feeding plate one by one through the capsule funnel, first pushed by the horizontal fork to the outer end of the correction block, and then Vertically and vacuum suction into the die hole, under the action of vacuum suction and separate the cap and body; the third station under the action of the track, the lower module descends and moves outward; the fourth station is filled with pellets, The pellets in the hopper pass the opening and closing action of the upper and lower switch plates to feed the pellets into the capsule body in the lower module; the fifth station is a transition station; the sixth station uses a blowing pipeline to open the cap body The defective capsules that have not been separated are removed and blown into the waste bucket collection and processing; under the seventh station, the module moves inward under the action of the rail and rises at the same time; the eighth station lock push rod rises under the action of the cam The filled capsule is locked; the ninth station discharge pusher rises under the action of the cam to push the locked capsule out and collect; the tenth station vacuum cleaner cleans the die hole and then enters the next cycle again.

Automatic Capsule Filling Machine This machine has variable frequency stepless speed regulation. It only needs to replace the measuring plate when changing the loading. It can be filled with 0#～4#} hard capsule by replacing the corresponding mold.